SATO GL4XXE Manual de Serviço Página 146
- Página / 204
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Unit 7: Replacement Procedures
GL4xxe Series Service Manual
7-7
OPERATION PANEL PCB REPLACEMENT
This circuit board provides the user interaction functionality via operational buttons and keys, as well as the LCD.
Before starting, turn the printer OFF and observe applicable lockout-tagout procedures.
1. Remove the printer’s front cover by releasing the thumbscrew (1) shown in Figure 7-5a. Slide the cover (2)
toward the electrical side of the printer (see arrows b and c) while prying it away from the main chassis.
2. Disconnect the cable set marked (3) in Figure 7-5b, and remove screw (4) before pulling the Operation
Panel (5) up and outward as shown by the black arrows.
3. The circuit board for the LCD panel circuit board (7) can be removed via three Bind P tight screws (6).
4. After replacing the necessary panels, reverse the disassembly procedure and perform adjustments to the
LCD contrast, Pitch Sensor, Print Density, Offset, Pitch and Buzzer Volume as necessary.
Figure 7-5a, Removing the front cover
Figure 7-5b, Removing the Operation Panel and LCD panel circuit board
- GL4xxe Service Manual 1
- O RADIO AND TV RECEPTION 2
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (cont’d) 4
- INTRODUCTION 7
- ABOUT THIS MANUAL 8
- GENERAL DESCRIPTION 9
- THEORY OF OPERATION 10
- CONTROL FEATURES 11
- Unit 1: Introduction 12
- GL4xxe Series Service Manual 12
- TECHNICAL DATA 13
- Unit 2: Technical Data 14
- REGULATORY 15
- CHARACTER FONT CAPABILITIES 16
- BARCODE CAPABILTIES 17
- INTERFACE 18
- SPECIFICATIONS 18
- INTERFACE SPECIFICATIONS 19
- SUPPORTED PROTOCOLS 20
- READY/BUSY INTERFACE SIGNALS 21
- IEEE1284 PARALLEL INTERFACE 22
- Table of IEEE1284 signals 23
- UNIVERSAL SERIAL BUS (USB) 25
- SOFTWARE SPECIFICATIONS 26
- 802.11G WIRELESS 27
- ALL INTERFACES 28
- RECEIVE BUFFER CONTROL 29
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- CHARTS AND DIAGRAMS 31
- PRINT SETUP DIMENSIONS 32
- LABEL PRINT DIRECTION 33
- LABEL ADJUSTMENT DIAGRAM 34
- READY/BUSY TIMING CHARTS 35
- X-ON/X-OFF TIMING CHARTS 36
- Unit 4: Charts And Diagrams 37
- CONFIGURATION 39
- PRINTER CONFIGURATION 40
- CONFIGURATION MODES 41
- CONFIGURATION MODE 42
- ADVANCED MODE 43
- SERIAL INTERFACE MODE 45
- PARALLEL INTERFACE MODE 46
- CENTRONICS INTERFACE MODE 47
- PGL EMULATION MODE 51
- ZGL EMULATION MODE 52
- DGL EMULATION MODE 53
- TGL EMULATION MODE 54
- IGL EMULATION MODE 55
- DIAGNOSTICS MODE 56
- PRINTER MANAGEMENT MODE 57
- MISC QUICK MENUS 58
- SOFT RESET 59
- KEY LOCK/UNLOCK 59
- MENU DEFINITION TABLES 60
- USER MODE (TABLE 4-1) 61
- ADVANCED MODE (TABLE 4-3) 67
- Data Protocol 80
- Buffer Size in K 80
- INTERFACES 90
- MENU DESCRIPTION 100
- EMULATION 101
- DIAGNOSTICS 120
- Priority Setting 120
- Command* 120
- IGL Setup 120
- Save state* 120
- Error Log Clear 122
- TROUBLESHOOTING 127
- ERROR TROUBLESHOOTING 128
- ERROR MESSAGES 129
- TROUBLESHOOTING TABLE 134
- NO PRINTED IMAGE 135
- INCORRECT LABEL POSITIONING 135
- SMEARED PRINT IMAGES 135
- INTERFACE TROUBLESHOOTING 136
- LAN ETHERNET INTERFACE 137
- 802.11G WIRELESS INTERFACE 137
- CENTRONICS INTERFACE 137
- TEST PRINT TROUBLESHOOTING 138
- Figure 6-2, Sample Test Label 139
- REPLACEMENT 140
- PROCEDURES 140
- REPLACEMENT PROCEDURES 141
- PLATEN ROLLER REPLACEMENT 142
- LABEL SENSOR REPLACEMENTS 143
- MAIN PCB REPLACEMENT 145
- POWER SUPPLY REPLACEMENT 147
- PCB during reassembly 148
- TIMING BELT REPLACEMENT 149
- RIBBON SENSOR REPLACEMENT 153
- HEAD-OPEN SENSOR REPLACEMENT 154
- RIBBON BOSS/TORQUE LIMITER 155
- Note the 156
- MEMORY CARTRIDGE REPLACEMENT 157
- INTERFACE BOARD REPLACEMENT 158
- CUTTER KIT REPLACEMENT 159
- REAL-TIME CLOCK REPLACEMENT 160
- Original front cover 162
- Figure 7-26, Replacement 170
- CHECKING / ADJUSTMENT 174
- PERFORMING TEST PRINTS 175
- RESETTING PRINT HEAD DATA 176
- SETTING THE LCD CONTRAST 178
- UPDATING THE PRINTER FIRMWARE 179
- HEAD OPEN SENSOR CHECKING 182
- PRINT DARKNESS ADJUSTMENT 183
- Pitch sensor holder 185
- I-Mark sensor position 185
- Gap Sensor position 185
- PRINT OFFSET ADJUSTMENT 186
- PRINT HEAD ALIGNMENT 187
- PRINT HEAD PRESSURE SETTING 188
- RIBBON TENSION ADJUSTMENT 190
- TIMING BELT ADJUSTMENTS 191
- SIMPLE DISPENSER ADJUSTMENT 193
- GLOSSARY 194
Manuais e produtos relacionados com Digitalizar e Imprimir SATO GL4XXE
Digitalizar e Imprimir SATO LM408e Manual de Serviço
(98 páginas)
(98 páginas)
Digitalizar e Imprimir SATO XL4xxe Manual do Utilizador
(114 páginas)
(114 páginas)
Digitalizar e Imprimir SATO CL608 Especificações
(12 páginas)
(12 páginas)
Digitalizar e Imprimir SATO GY412 Manual de Instruções
(217 páginas)
(217 páginas)
Digitalizar e Imprimir SATO XL400 Manual do Utilizador
(194 páginas)
(194 páginas)
Digitalizar e Imprimir SATO M8485Se Manual de Serviço
(216 páginas)
(216 páginas)
Digitalizar e Imprimir SATO CG412TT Manual do Utilizador
(102 páginas)
(102 páginas)
Digitalizar e Imprimir SATO XL4xxe Manual do Utilizador
(121 páginas)
(121 páginas)
(73 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais