SATO RWG500 Especificações Página 1

Quick GuideFor Rewinder: RWG500www.satoamerica.comPN: 9001128 (B)

8Parts IdentificationSelector for clockwise or counterclock-wise rewind directionSocket for AC adaptorEXT connector (links to printer)Earth terminalPo

9Preparing the Joint PlateThe joint plate aligns the base of the RWG500 to the base of a SATO printer. This alignment ensures a smooth label path and

10Preparing the Joint Plate (cont’d)To prepare the joint plate for a GT4XXe or M84Pro series printers:When the movable plate reveals “GT4XXe” and “M84

11Preparing the Joint Plate (cont’d)To prepare the joint plate for the M5900RVe printer:Top of movable plateBossBossUnderside of movable plateWhen the

12Preparing the Joint Plate (cont’d)To prepare the joint plate for the CL6XXe series printers:Top of movable plateBossBossUnderside of movable plateWh

13Adjusting the Roller HeightBefore the rewinder is guided into place in front of the printer, the height of its first roller has to be adjusted to on

14Installing the Joint PlateTo align the printer to the RWG500 using the joint plate:1Place the non-movable holes of the joint plate under the feet of

15Installing the Joint Plate (cont’d)3Now place the printer so that its feet at the label output side will fit into the positioning holes on the joint

16Configuring the RewinderThis section shows how to configure the label rewinder for operation. Choose the option identified below that best reflects

17Configuring the Rewinder (cont’d)Rewind Mode 3This rewinding mode synchronizes rewinder operation with the feeding printer.When the assigned printe

SATO America, Inc.10350A Nations Ford RoadCharlotte, NC 28273Main Phone: (704) 644.1650Technical Support: (704) 644.1660Technical Support Fax: (704) 6

18Configuring the Rewinder (cont’d)DIP SWITCH CONFIGURATIONFUNCTION DSW1DSW 2DSW 3DSW 4DSW 5DSW 6Rewind Mode 1 OFF OFF OFF OFF OFF OFFRewind Mode 2 O

19Label SetupThe RWG500 offers two rewind directions and two types of rewind shafts, as follows:Rewinding Direction: Face in (CW) / Face Out (CCRewi

20Label Setup (cont’d)To change the rewind direction, use the Direction switch found on the side panel of the rewinder. The factory set-ting is CW rew

21Label Setup (cont’d)Besides setting the rewind direction, you can set up the rewinder for direct rewinding or rewinding using a 3” paper core. About

22Label Setup (cont’d)You can collect output labels onto a 3” paper core for more consistent winding, and if the wound label needs to be unwound later

23Label Setup (cont’d)After properly inserting the 3” core adaptor(s), follow the steps below to install the label.3Insert the 3” paper tube core into

24Basic OperationAfter setting up the rewinder to work with your SATO printer, rewinding can be performed.1Turn on the rewinder. Wait for the status L

25Basic Operation (cont’d)Start the automatic rewinding by printing labels on the printer. Each time a label is printed, the rewinder automatically wi

26Winding 7” labelsTo wind labels wider than 131 mm, the optional 7” Expan-sion Kit is required. The kit consists of the following:1 Second roller j

27Installing the 7” Expansion KitFollow the steps below to install the Expansion Kit.Remove the cap covering the second roller of the rewinder.Insert

1IntroductionThank you for your purchase of the SATO RWG500 new generation rewinder for SATO barcode printers.This quick reference guide will lead you

28Installing the 7” Expansion Kit (cont’d)Remove the cap covering the rewinding shaft of the rewinder.Insert the core joint and core shaft guide. Tigh

29Basic SpecificationsRewinding method• Ø 38.1 mm direct rewinding • 3” paper core rewindingPaper typeSupports all genuine SATO labels printed on SATO

2Safety SymbolsAbout warning symbolsAs a preventive measure to ensure safe usage of this machine so as to safeguard against damage to yourself, other

3Safety PrecautionsDo not place on an unstable placeDo not place the rewinder on an unstable place such as an unsteady table, an inclined place or a p

4Abnormal ConditionsDo not use the rewinder if it is emitting smoke or strange odors. Continued use creates the danger of fire and electrical shock.*

5FCC NoticeThe equipment referenced in this document complies with the requirements in Part 15 of FCC Rules for a Class B Computing Device. Operation

6What’s In the BoxRWG500 main unit Joint plateEXT cableLabel Clip3-inch core x 2 Label GuideQuick Guide

7Parts IdentificationSecond rollerFirst rollerTension armRewindStart/Stop buttonStatusLEDDirection Indicator LED:Clockwise winding (face in)Direction