SATO CT400i Series Manual de Instruções

Thank you for purchasing the SATO CT400i Series barcode printer. Please read this manual carefully to ensure you understand the CT400i Series function

Loading the Roll Paper [Continuous, Cutter, Linerless types]While pressing the paper holder slide lever (1), adjust the paper holder to match the pape

Close the top cover.At this time, press on the top where shown by the arrows to close the cover until you hear the lock engage.(1) Press the [FEED] ke

Loading fan-folded paper [Continuous, Cutter types]Press down on the open lever (1) on the right side of the printer to release the lock and then open

Loading fan-folded paper [Continuous, Cutter types]While pressing the paper holder slide lever (1), adjust the paper holder to match the paper size (2

Loading Roll Paper [Separator]Open the front cover forward.Press down on the open lever (1) on the right side of the printer to release the lock and t

Loading Roll Paper [Separator]Pass the backing paper between the separator unit and the platen roller.Set the backing paper so that it is below the se

Loading Roll Paper [Separator]Be careful not to become injured when replacing paper.After printing, the thermal head and surrounding area are hot. Be

Printing Position Adjustment▲Printing Standard PositionThe printing standard position when using labels is the top of the label.The printing standard

Cut Position Adjustment▲Label Cut▲Cutting paper with perforated linesThe cut position when using labels is the designated cut position between labels

Loading the Carbon Ribbon[Loading the Carbon Ribbon]Press down on the open lever (1) on the right side of the printer to release the lock and open the

2EnglishGermanChineseKoreanYou are cautioned that changes or modifi cations not expressly approved by the party responsible for compliance could void y

After setting the carbon ribbon in the right side of the ribbon supply unit (1), press the core guide (2).3After setting the ribbon core in the right

Loading the Carbon RibbonFor carbon ribbon with a width of 76 mm or 59 mm, set the ribbon adapter hooks at the bottom. From this state, turn the hooks

Closing the top cover after closing the ribbon unit could prevent the top cover from closing properly. Always put the ribbon unit in the top cover.Cau

[Standard Interface]¡ USB + LAN type(1)When using a USB interface, set DSW 1-8 inside the front cover to OFF.When using a LAN interface, set DSW 1-8 i

[Extension Interface(Option)]¡ IEEE 1284 interfaceIEEE 1284 interface(1)When using an IEEE 1284 interface, set DSW 3-1 of the circuit board on the bot

¡ Bluetooth interfaceBluetooth interfaceThe Bluetooth interface board is contained inside the printer and cannot be seen from outside.Connecting to a

Turning On the PowerPlug the AC adapter/power cord into the printer and turn on the power.[Power Setting]When installation is completed, set the power

Turning On the Power[Turning On the Power]Turn on the power switch at the front of the printer.Switch it to the “ ” symbol.When the power switch is t

[Printer Status Print]Printing Operation Confirmation and Error Number DisplayThis prints the status of the printer.The current settings information i

*A detailed explanation of the dip switches is given on the explanation sticker affixed to the printer.* The head check is a head disconnection guidel

Version 1 December 10, 2007 Q02073000©2007 SATO CORPORATIONSafety PrecautionsPictographic SymbolsThis instruction manual and the printer labels uses a

Function ExplanationData bit lengthParity bitStop bitBaud rateCommunication protocolOFF: 8 bitON: 7 bitDSW2-2OFFOFFONONDSW2-3OFFONOFFONParity bitNoneE

Printing Operation Confirmation and Error Number DisplayNo.(1)(2)Function ExplanationNot usedInterface settingsNormally OFFUSB interface (DSW1-8 OFF)L

Resolution MethodCauseError Code¡Error Messages023456789AbcdrFLASH ROM read/write overflow or write count overflow.Defective circuit boardEEPROM error

CT408iDT/CT408iTTMaximum 6 inchs (Approx. 150 mm/s) Maximum 4 inchs (Approx. 100mm/s)Max. 3 inchs (Approx. 75 mm/sec)8-dot/mm (203 dpi)Model namePrint

Environmental conditionsOperation ambient temperature: 5 to 35°CHumidity: 30 to 80% (However, no dew formation)Storage ambient temperature : -5 to 60°

OCR-A 15×22 dots(alphanumeric, symbol)OCR-B 20×24 dots(alphanumeric, symbol)OCR-A 22×33 dots (alphanumeric, symbol)OCR-B 30×36 dots (alphanumeric, sym

Safety PrecautionsCaution(1)(2)(3)Reproduction in any manner of all or part of this document is prohibited.The contents of this document may be change

Accessories Check¡Quick Guide¡Safety manual¡Manual (for RoHS) ¡GWP leaflet¡ Power cord and AC adapter¡ Test labels and ribbons¡ Dial adjustment screwd

[Back (USB + LAN interface)]¡DC input power terminal (Power connector)¡USB interface¡LAN interface¡I/F Cover¡I/F Cover[Back (USB + RS-232C inte

Names of PartsWhen top cover is opened¡ Thermal head¡ Paper holder¡ Paper sensor¡ Platen roller¡ Paper holderslide lever¡ Paper holder¡ Ribbon unit¡ P

Names of Parts(When front cover is open)(When front cover is open)¡ Cutter top knife¡ Cutter bottom knife¡ Cutter unit¡ Paper holder¡ Paper sensor¡ Pl

Names of Parts[Operation Panel]¡ [POWER] lamp[When the front cover is opened]Illuminates (green) when the power switch is on.¡ [ERROR] lampIlluminates